Recommended Break-in Procedures for Engines
This engine has been rebuilt to give long, satisfactory service. Protect your investment by following these instructions before installing or starting the engine.
Suggested PreCAUTIONs for Remanufactured Engines
This engine has been carefully remanufactured to precision standards, and
will perform properly if certain steps are taken by the mechanic making
the installation. Following is a list of causes for remanufactured engine
to fail early in service, and suggested procedures to prevent failure.
When a properly remanufactured engine fails to give satisfactory service,
it is usually due to: burning
piston heads caused by detonation, pre-ignition or "lugging";
piston scuffing or seizing usually caused by overheating or excess fuel;
bearing and crankshaft wear caused by under-lubrication, dirt or coolant
seepage; excessive piston and cylinder wear caused by dirt, ineffective
air filtering, coolant seepage or excessively rich, air-fuel ratio.
The customer and the remanufacture have a mutual interest in this engine.
We both want it to perform and give long and satisfactory life.
We recommend these precautions:
1. Be sure to prime the oil pump, oil lines and fill the oil filters with oil using an auxiliary pump, operating the internal oil pump with a hand drill, or an external pressure tank connected to the oil pressure gauge or sending unit fitting before starting the engine. It is desirable to fill the crankcase in this manner. If using an air pressure tank be sure it does not run out of oil and blow air through the lines.
2. Proper air-fuel ratio is vital in today's engines. Be sure the carburetor
or fuel injection system has been remanufactured to manufacturer's specifications.
Manifold and cylinder head surfaces should be
checked and in good condition (resurface if necessary). Be sure the cylinder
heads and manifolds aretorqued and retorqued in proper sequence if required.
Air seepage can cause lean air-fuel ratio which causes detonation. Check
fuel pump for proper pressure.
3. Ignition or diesel fuel injection system should be properly serviced
or calibrated, and engine timing corrected. Proper valve lash or clearance
is very important.
4. Be sure to use spark plugs of the correct heat range and gap as specified by the engine manufacturer. Check electronic sensors and sending units for proper operation. Vacuum lines must be properly routed and connected to the appropriate fittings to ensure operation of emission control devices and related engine controls.
5. Check the exhaust thermostat control (commonly called the heat riser) to be certain it is free and operating properly. Check the exhaust gas re circulation valve (EGR valve) for proper operation. Clean the intake manifold to remove deposits from the various passages.
6. Rebuild or replace the radiator and hose lines to ensure they are free from deposits so that the cooling system can function properly. Restrictions can cause overheating. Thermostats should be checked or replaced with one of the correct temperature. Use the proper pressure cap as specified by the engine manufacturer, and make sure it is properly seated.
7. Important -replace filter elements. Thoroughly check engine accessories which are to be reused. Clean them internally and externally before installing.
8. The coolant used should be compatible with aluminum engine components and blended to a mixture of no more than 60% antifreeze and 40% water. We recommend that a good sealer with rust inhibitors be added to the cooling system. This will tend to prevent rust and scale deposits and guard against coolant seepage.
9. Before releasing the engine for regular service, check the air-fuel ratio. Caution the driver against "lugging."
RECOMMENDED "BREAK-IN" PROCEDURES FOR REMANUFACTURED ENGINES
Protect the investment you have in your engine. Take the time to read and
follow these recommendations.
CAUTION
1. Before starting the engine for the first time, be sure it has been properly
pre-lubricated.
2. Never add cold water to the cooling system while the engine is running.
The engine should be allowed to run at normal operating temperature.
3. Start engine and run at fast idle, approximately 1500 RPM, and check
the oil pressure. Run the engine for 30 minutes even though coolant may
rise to operating temperature in a few minutes. Adjust tappets,if required,
carburetor and ignition timing. If the coolant should "boil over," stop
engine and allow to cool.Then start again and proceed as above.
4. When required retorque cylinder heads and manifolds to engine manufacturer's
specifications in proper sequence. Readjust tappets if necessary.
5. Start engine again and make a test run on the road at 30 MPH in "drive" range
or select the proper gears for standard transmission. Periodically accelerate
to 50 MPH and decelerate rapidly. Repeat this procedure at least 10 times.
For a large truck or industrial engine, accelerate in intermediate gears
as above.
NOTE: Applying loads to the engine for short periods of time causes increased
ring pressure against the cylinder walls and helps to seat the rings. This
is especially important because you are "breaking-in" the engine
with heavy duty oils. The rapid deceleration increases vacuum and gives
extra lubrication to the piston and ring assemblies.
Engine or Vehicle Service Recommendations
Passenger Cars
Drive normally but not at continuous high speeds or under heavy loads for
the first 500 miles. Change oil and filters after 500 miles.
Trucks
Operate the vehicle with light loads up to 500 miles and avoid "lugging." Occasional
acceleration and deceleration in proper gear during this period is advisable.
Change oil and filters after 500miles of service.
Industrial Engines
Follow the above instructions and operate under partial loads for several
hours. Change oil and filters after approximately 20 hours of operation.
As required by the engine or gasket manufacturer, after 1000 miles of service,
retorque cylinder heads and manifolds to proper specifications. Readjust
tappets when required. We suggest this be done again after 5000 miles. We
know that this means extra work, but it assures long and satisfactory engine
performance.
DESIGNATION, IDENTIFICATION AND DESCRIPTIONS OF OIL CATEGORIES API Engine
Service Description
Letter Designations: SA, SB, SC, CA, CB
Oils with this designation are considered obsolete and should not be used
unless specifically authorized by the engine manufacturer.
Letter Designation: SD
1968 Gasoline Engine Warranty Maintenance Service ...typical of gasoline
engines in 1968 ¬1970 models of passenger cars and some trucks operating
under engine manufacturer's warranties in effect during those model years.
Oils designed for this service provide more protection against high - and
low-temperature engine deposits, wear, rust, and corrosion in gasoline
engines than oils which are satisfactory for API Engine Service Categories
SC and maybe used when category SC is recommended.
Letter Designation: SE
1972 Gasoline Engine Warranty Maintenance Service ...typical of gasoline
engines in passenger cars and some trucks beginning with 1972 and certain
1971 models operating under engine manufacturer's warranties. Oils designed
for this service provide more protection against oil oxidation, high temperature
engine deposits, rust and corrosion in gasoline engines than oils which
are satisfactory for API Engine Service Categories SD or SC and may be
used when either of these categories is recommended.
Letter Designation: SF
1980 Gasoline Engine Warranty Maintenance Service ...typical of gasoline
engines in passenger cars and some trucks beginning with 1980 - 1988 model
years operating under engine manufacturer's recommended maintenance procedures.
Oils developed for this service provide increased oxidation stability and
improved anti-wear performance relative to oils that meet the minimum requirements
for API Service Category SE. These oils provide protection against engine deposits,
rust and corrosion. Oils meeting API Service Category SF may be used where categories
SE, SD or SC are recommended.
Letter Designation: SG
1989 Gasoline Engine Service - Service typical of gasoline engines in present
passenger cars,vans and light trucks operating under manufacturer's recommended
maintenance procedures .Category SG quality oils include the performance
properties of API Service Category CC. (Certain manufacturers of gasoline
engines require oils also meeting API Service Category CD). Oils developed
for this service provide improved control of engine deposits, oil oxidation
and engine wear relative to oils developed for previous categories. These
oils also provide protection against rust and corrosion. Oils meeting API
Service Category SG may be used where categories SF, SE,SF/CC or SE/CC
are recommended.
SH
This oil classification came to the industry in 1992 to replace the SG
oil and provide better protection against rust, oxidation, sludge, varnish
as well as providing extended component life expectancy. It is currently
still available, however it is obsolete for PCMO licensing. It can be used only
with API CF, CF-2, DF-4 and CG-4 when displayed in the API service symbol
and the Category appears first.
SJ
This oil classification came to the industry in 1996 to replace the SH
oil with continued refinements to the SH oil. It is currently available
and acceptable for use in engines manufactured previous to the year 2,000.
ILSAC GF-3
(ILSAC, International Lubrication Standardization & Approval Committee)
This oil meets the current automotive manufacturer requirements for their
newest lines of engine sand will be used in 2,000 automotive engines. There
were earlier versions used before the year 2000. The ISLAC grades are described
as SAE 0W-20, 0W-30, 5W-20, 5W-30, 10W-30. These oils have improved overall
oil performance while increasing fuel economy while providing emission systems
protection.
Letter Designation: CC
Moderate Duty Diesel and Gasoline Engine Service - Service typical of certain
naturally aspirated,turbo charged, or supercharged diesel engines operated
in moderate to server-duty service and certain heavy-duty gasoline engine.
Oils designed for this service provide protection from high-temperature
deposits and bearing corrosion in these diesels and also from rust corrosion,and
low-temperature deposits in gasoline engines. These oils were introduced
in 1961.
Letter Designation: CD
Severe Duty Diesel Engine Service - Service typical of certain naturally
aspirated turbo charged or supercharged diesel engines where highly effective
control of wear and deposits is vital or when using fuels of wide quality
range including high sulfur fuels. Oils designed for this service we reintroduced
in 1955 and provide protection from bearing corrosion and from high-temperature deposits
in these diesel engines.
Letter Designation: CD-II
Severe Duty Two-Stroke Cyclic Diesel Engine Service - Service typical of
two-stroke cycle diesel engines requiring highly-effective control over
wear and deposits. Oils designed for this service also meet all performance
requirements of API Service Category CD.
Letter Designation: CE
Severe Duty Diesel Engine Service - Service typical of certain naturally
aspirated, turbocharger supercharged heavy duty diesel engines manufactured
since 1983 and operated under both low speed - high load and high speed
- high load conditions. Oils designed for this service must meet the requirements
of API Engine Service Category CC and CD.
LUBRICANT RECOMMENDATIONS FOR "BREAKING-IN" REMANUFACTURED ENGINES
Follow the recommendations of the engine manufacturer for the proper viscosity
and type of oil to be used during and after the "break-in" period.
It is important to use heavy-duty detergent oils which contain an EP (extreme
pressure) additive right from the start. Special "break-in" oils
should not be used unless specified by the manufacturer. Older engines
without oil filters may require special considerations, such as the use of
non-detergent oils unless otherwise specified by the manufacturer.
Consult the owner's or service manual for the latest manufacturer's recommendation
on oil selection.
See the accompanying chart for additional information on the type of engine
oils currently in production and available for use with today's engines
SAE Motor Oil Viscosity Classifications
Since 1911, the petroleum industry has used the SAE Crankcase Oil Viscosity
Classification System to describe and classify motor oils according to
their ability to flow at various temperatures. The grades in common used
today are: 5W, 10W, 15W, 20, 30, 40 and 50. The"W" indicates
the oil is suitable for use during low ambient temperatures such as during
the winter months. For instance, oils designated at 5W-30 provide adequate
lubrications at -13°F (-25°C).Multi grade oils are able to maintain their
viscosity over a wide range of temperatures. An oil designated as 10W-40
performs as well as a 10W designated oil at low temperatures, and as well
as a single grade 40 designated oil at high temperatures.
Synthetic Motor Oils
The introduction of synthetic motor oils dates back to World War II and
they are often described as the "oil of the future." Synthetic
oils are man made, manufactured in a laboratory rather than pumped out of
the ground and refined. They offer a variety of advantages over natural
oils from better fuel economy, stability over a wide range of temperatures
and operating conditions and longevity.
However, the use of synthetic engine oils is not recommended for the "break-in" period.
Its outstanding ability to reduce wear by virtually eliminating friction
between moving components is not desirable for a "break-in" oil.
Certain predictable amounts of friction are required for proper "break-in" of
piston and piston rings. AERA does not recommend the use of synthetic engine
oils for the first 5,000 miles of service. Thereafter it is up to the vehicle
owner to weight the cost of more expensive synthetic motor oils, manufacturer's
oil classification recommendations and drain intervals.
Abbreviations and Symbols
API - American Petroleum Institute
SAE - The Society of Automotive Engineers
© AERA 1999 - All Rights Reserved
This information is provided from the best available sources, however,
AERA does not assume responsibility for data accuracy or consequences of
its applications. Please be aware that this pamphlet is not a warranty.